Singer W213 Manual de usuario

INSTRUCTION MANUAL FORSEWING MACHINEWHiTeCall Toll Free 800-331-3164 www.whitesewtrKi.eom

WINDING THE BOBBIN1 .Release stop motion knob.a.Thread as shown.3. When the bobbin is full, the stop niotion knob must be tightened.5cm threadPush b

REMOVING BOBBIN CASE AND BOBBIN1.Raise needle to Its highest position and open the shuttle race cover.2.0pen hinged latch of bobbin case a

INSERTING BOBBIN CASE INTO SHIHUE RACE1.Raise needle to its highest position, pulling thread to the front, open the latch of bobbin case and hold it.2

THREADING UPPER THREADTwin needle threading

DRAWING UP BOBBIN THREAD1. Hold upper thread with left hand, turn the hand wheel slowly towards you until the needle qoes down and com

levelung machineDOWNUPt1

ADJUSTING THREAD TENSIONIt is only normally necessary to adjust the uf^er thread tension to achieve the correct balance between the up

REGUUTING THE PRESSER FOOTPRESSURE1- Push down lever for desired pressure, for light fabrics set iever at 1, set at 2 for medium fabrics and 3 for hea

CHANGING NEEDLE1. Raise needle bar to its highest position.2. Loosen needle clamp screw and remove old needte.3. With the flat side of the needle fac

FABRIC THREAD NEEDLE TABLE_ 15_

POLAmZED PLUGS CAUTIONThis product is equipped with a polarized alternating current line plug (a plug having one blade wider than the

TO START SEWINGImportant Hints1. Raise the take-up lever to its highest position before starting ancf after stopping sewing.2. Hold both

TO FINISH SEAM2. Push the reverse button and sew in reverse for about 3-4 cms.3. Raise needle to its highest position.4. Lift presser foot and pull

STRAIGHT STITCH1 .This type of stitching is the one used most frequently.2. The zig-zag presser foot can be used for both straight and zig-zag sewing

BUTTON SEWING1 .Lower drop feed.2. Place buuon attaching presser foot in position.3. Raco button between presser foot and fabric and lower presser f

ZIPPER SEWINGSelect straight stttch.1. Zipper foot is designed to sew close to a raised edge preventing sewing on zipper2. Race zipper fo

HEMMING Note; Hemmer foot can be purchased separately.1. Raise the foot artd the needle to .its highest position. Replan the foot with

TWIN NEEDLENote; Twin needle can be purchased separately.Remove regular needle and insert twin rreedle. Thread bottr threads through the sa

QUILTER Note: Quilt guide can be purchased separately.1 .Slide arm through hole on top of presser foot holder. 2.Move guide to reguired stitch distanc

BUTTONHOLE SEWINGTo prepare:1. Mark the location of buttonhole on your garment.2. Attach the all purpose foot t t3. Set the stitch length dial haM

MAINTENANCE (CLEANING AND OILING)Cleaning shuttle race(A) Latch knob(B) Shuttle race cover(C) Shuttle hook1. Raise needle to its highest position.

IMPORTANT SAFETY INSTRUCTIONS...Whsn using an electrical aopiiance. basic safety precautions shouW always befollowed, including the following.Read

PROiSLEMPROBABLE CAUSECORRECTIONFabric not moving- Feed dog down.- Machine not moving.- Stitch iengdt dial in 0 position.- {.i^t pres^re on pretsa

CONTENTSNames of Parts...1 ^ 2Accessofies...

NAME OF PARTS (FRONT VIEW)• 1. Use a soft cloth to clean themachine.2. Do not expose the machine to direct sunlight.

(REARVIEW)

тттВоШпSpool pin Шí^psaghM(OnmacMne)2^црвгШButkm 88won foctfNe«de$ ill #14- 3

BEFORE SEWINGMachíne plug1. Fit plug into the machine.2. Plug the machine to the power supply.Power supply 3 Sewing speed carj be varied by the foot

REMOVING EXTENSION TABLEi.HoJd the left end of table and pull out in direcfion or arrow.FREE-ARM SEWING1. This sewing machine can be us