Singer 14U354B Manual de usuario

14U344B/354B3-4THREAD OVERLOOK MACHINEOperator’sGuideSINGER

8. HOW TO REMOVE AND INSERT NEEDLES• TO REMOVE NEEDLE (S)* Be sure to disconnect the machine from the electric outlet before removing needle(s).* T

9. HOW TO REMOVE CYLINDER COVER^ Removing the cylinder cover exposes the lower looper for easy threading and cleaning of the machine.* While

11. THREADING THE MACHINE• THREADING DIAGRAM* A color coded threading diagram is located inside the looper cover for quick reference.* Thread the m

* Pass thread from back to the front through the thread guide 0.* Insert thread through the right hole.* Bring thread up and insert through top of l

(2) Threading the Lower Looper (Yellow)* Thread the lower looper as indicated ©Pass thread from back to the front through the thread guide ©.

* Thread the looper area of the machine following the yellow color coded thread guides ®'^(6).* Remove the cylinder cover (page 9) to expose the

(3) Threading the Right Needle (Green)* Thread the right needle as indicated (D .* Pass thread from back to the front through the thread guide ®.* I

* Continue to thread points 0 '^©.Note: Be sure to pass the thread through upper thread path of the thread guide* Thread the eye of the right ne

(4) Threading the Left Needle (Blue)* Thread the left needle as indicated © .* Pass thread from back to the front through the thread guide ©.* Inse

* Continue to thread points 0 ^(7).Note: Be sure to pass the thread through lower thread path of the thread guide®.* Thread the* eye of the left need

14U 344B/354BPREFACEThank you for your purchase of this sewing machine.This machine intended for household use will provide you with excellent perform

12. CHAINING OFFANDTEST SEWING* When the machine is completely threaded, bring all of the threads over the throat plate and slightly to the le

13. BASIC STITCH TYPES• 4 THREAD OVERLOOK MOCK SAFETY STITCH* This machine is a four-thread overlock that uses two needles and two loope

• SUGGESTED TENSION SETTINGS FOR 4 THREAD OVERLOOK MOCK SAFETY STITCHNote:* These are suggested tension settings only.* Tension settings are effecte

* SUGGESTED TENSION SETTINGS FOR THE 3 THREAD OVERLOOK STITCHNote:* These are suggested tension settings only.* Tension settings are effected by1)

15. HOW TO CHANGE THREADS/TIE ON METHOD* To change thread type or color, clip thread near the spool.* Place new thread on stand.* Tie new thread an

* Pull the threads through the machine one at a time.* If threads do not pull easily, check for tangles on thread guides or looping under thread sta

* TO PLACE MOVABLE KNIFE IN WORKING POSITION* Open looper cover and push the movable knife holder to the right as far as it will go.* Turn the knob

19. HOW TO ADJUST THE OVEREDGE SEAM WIDTH* The machine is set to sew the 4 thread stitch and three thread left needle position stitch

20. HOW то SEW A ROLLED HEMRolled hemming is done by rolling and overedging the fabric edge.* Light weight fabrics such as lawn, voil, organdy, crep

* Set the stitch length dial to “2^F” and a fine seam will be sewn.* This machine can sew two types of rolled hems.* SUGGESTED TENSION SETTINGS FOR

IMPORTANT SAFETY INSTRUCTIONSWhen using this machine, basic safety precautions should always be followed including the following.Read all

When the lower looper thread is too loose— Turn the lower looper thread tension dial (yellow) toward a higher number.— Or, turn the upper looper threa

21. stTtch variations andSEWING TECHNIQUES* HOW TO SEW A FLATLOCK DECORATIVE SEAM* A flatlock stitch is achieved by adjusting the tension of

* Pull on opposite sides of the seam to pull the stitches flat.(3) Decorative Flatlocking* Place the movable upper knife in the non-work

• HOVC то SEW AN OVERLOOK BLIND HEMThe excess fabric is trimmed and the hem is sewn and the raw edges are overlocked in one operation.The ove

* Fold the fabric with the wrong sides together and sew.Press the pin tucks in the same direction.* TURNING SQUARE CORNERS(1) Outside Corne

* Place movable upper knife in non-operating position (page 23).* Stitch on cut edge of fabric.* Stop sewing before you reach the corner and

• APPLYING ELASTIC* Place the movable upper knife in the non-operating position, (page 23)* Divide the elastic and the area where the ela

* HOW TO REINFORCE A SEAM* inserting twill tape while overedge sewing will stabilize the seam.* Insert the tape through the hole in the front of th

* DIFFERENTIAL FEED(with differential feed machine only)* Differential feed is a system which “stretches” or “gathers” the fabric, when amount

(2) Stretch overedge(Use regular or rolled hemming throat plate)* Stretch overedge is ideal for sewing decorative collars, sleeves, skirt hems,

Never drop or insert any object into any opening. ^ Do not use outdoors. Do not operate where aerosol (spray) products are being used or where

22. HOW TO ADJUST THE PRESSER FOOT PRESSUREThe presser foot pressure of the machine is preadjusted for sewing medium weight fabrics.* It m

24. RELATIONSHIP BETWEEN CLOTH, THREAD AND NEEDLEType of Fabric Type of ThreadNeedleSinger Cat. No. 2054Light WeightLawn, Organdy, Voil, Crepe, etc.C

25. MACHINE MAINTENANCE* An overlock requires more maintenance than a conventional machine mainly due to two reasons.1) A lot of lint is produc

* HOW TO REPLACE THE STATIONARY KNIFEDanger: Before replacing the stationary knife, disconnect power line plug from the wall receptacle.

• HOWTO EXCHANGE LIGHT BULBDanger: Always unplug before relamping.* Light bulb is available at your Singer shop. Take old bulb to the Singer shop a

26. TROUBLESHOOTING CHARTProblemSolutionPageFabric does not— Lengthen stitch length23feed well— Increase presser foot pressure for heavy weight fabri

27. OPTIONAL ACCESSORIES AND ATTACHMENTS(1) Sewing with an Overlook* For additional information, the following book is recommended. Sewing w

(5) Ultra Hem Foot (P/N 376719)* Special foot that makes sewing a blind hem easier. The machine will trim the excess fabric, finish off the edge and

Form U6195 (Rev. 492)Part No. 379371-002 (Rev. 1) Printed in Japan

CONTENTSPage1. Accessories...42. Needle information...43.

1. ACCESSORIESNeedle set 1Screwdriver (sheet metal) 1Screwdriver (small size) 1Tweezers 1Rolled hemming throat plate 1Hex-head wrench 1See page

3. PRiKiCIPAL PARTS® Thread guides and holder d) Handle(3) Pressure regulating screw 0 Left needle thread tension dial (blue)(D Right needle thread t

4. HOW TO OPEN LOOPER COVER* Push the cover to the right as far as it will go. (f)* Pull cover down toward you. @Caution:Be sure looper cover is cl

Warning:* Be sure that the electrical voltage of the electric outlet (wall receptacle) is the same as the rated voltage of the motor.* Handle the